Emoncms and RPICT on the same Raspberry: Difference between revisions
No edit summary |
No edit summary |
||
| Line 3: | Line 3: | ||
This is a stand alone solution where data are acquired and recorded on the same device. | This is a stand alone solution where data are acquired and recorded on the same device. | ||
==Download and write image== | |||
First you should download the latest emonSD image from this link below. | First you should download the latest emonSD image from this link below. | ||
| Line 10: | Line 12: | ||
Flash this image onto a SD card. Before inserting the SD card on the Raspberry create and empty file called '''ssh''' inside the boot partition. | Flash this image onto a SD card. Before inserting the SD card on the Raspberry create and empty file called '''ssh''' inside the boot partition. | ||
==Modify Emonhub Config== | |||
Insert the SD card and connect the power supply. Once the Raspberrypi fully powered up point your web browser to http://emonpi. | Insert the SD card and connect the power supply. Once the Raspberrypi fully powered up point your web browser to http://emonpi. | ||
On | On the left panel select '''Emonhub'''. Then click on '''Edit Config'''. | ||
You can now modify the emonhub configuration as shown below. | You can now modify the emonhub configuration as shown below. | ||
Find | Find the section below. | ||
| Line 38: | Line 40: | ||
# interval = 300 # Interval to transmit time to emonGLCD (seconds)</nowiki> | # interval = 300 # Interval to transmit time to emonGLCD (seconds)</nowiki> | ||
Delete this text and replace with this | Delete this text and replace with this one below | ||
<nowiki>[[SerialDirect]] | <nowiki>[[SerialDirect]] | ||
| Line 48: | Line 50: | ||
pubchannels = ToEmonCMS,</nowiki> | pubchannels = ToEmonCMS,</nowiki> | ||
In the same way find the section | In the same way find the section with | ||
<nowiki>[[11]] | <nowiki>[[11]] | ||
nodename = 3phase | nodename = 3phase | ||
| Line 66: | Line 68: | ||
units = W,W,W,W,W,W,W,W</nowiki> | units = W,W,W,W,W,W,W,W</nowiki> | ||
Note that you will certainly have to adapt this last section of the configuration yourself to make it match with your RPICT hardware. Check the data | Note that you will certainly have to adapt this last section of the configuration yourself to make it match with your RPICT hardware. Check the data output section on the specific board page. | ||
Revision as of 09:15, 3 May 2022
This guide will show how to setup for Emoncms and the RPICT board hosted on the same Raspberry pi.
This is a stand alone solution where data are acquired and recorded on the same device.
Download and write image
First you should download the latest emonSD image from this link below.
https://github.com/openenergymonitor/emonpi/wiki/emonSD-pre-built-SD-card-Download-&-Change-Log
Flash this image onto a SD card. Before inserting the SD card on the Raspberry create and empty file called ssh inside the boot partition.
Modify Emonhub Config
Insert the SD card and connect the power supply. Once the Raspberrypi fully powered up point your web browser to http://emonpi.
On the left panel select Emonhub. Then click on Edit Config.
You can now modify the emonhub configuration as shown below.
Find the section below.
### This interfacer manages the RFM12Pi/RFM69Pi/emonPi module
[[RFM2Pi]]
Type = EmonHubJeeInterfacer
[[[init_settings]]]
com_port = /dev/ttyAMA0
com_baud = 38400 # 9600 for old RFM12Pi
[[[runtimesettings]]]
pubchannels = ToEmonCMS,
subchannels = ToRFM12,
group = 210
frequency = 433
baseid = 5 # emonPi / emonBase nodeID
calibration = 230V # (UK/EU: 230V, US: 110V)
quiet = true # Disable quite mode (default enabled) to enable RF packet debugging, show packets which fail crc
# interval = 300 # Interval to transmit time to emonGLCD (seconds)
Delete this text and replace with this one below
[[SerialDirect]]
Type = EmonHubSerialInterfacer
[[[init_settings]]]
com_port = /dev/ttyAMA0
com_baud = 38400
[[[runtimesettings]]]
pubchannels = ToEmonCMS,
In the same way find the section with
[[11]]
nodename = 3phase
[[[rx]]]
names = powerL1, powerL2, powerL3, power4, Vrms, temp1, temp2, temp3, temp4, temp5, temp6, pulse
datacodes = h,h,h,h,h,h,h,h,h,h,h,L
scales = 1,1,1,1,0.01,0.01,0.01,0.01,0.01,0.01,0.01,1
units = W,W,W,W,V,C,C,C,C,C,C,p
delete and replace with this text below.
[[11]]
nodename = rpict8
[[[rx]]]
names = power1, power2, power3, power4, power5, power6, power7, power8
scales = 1,1,1,1,1,1,1,1
units = W,W,W,W,W,W,W,W
Note that you will certainly have to adapt this last section of the configuration yourself to make it match with your RPICT hardware. Check the data output section on the specific board page.