View source for EmonWRT3 Network Locked Out



=Overview=

This page will help you restoring the EmonWRT3 system if the device can not connect to any network after misconfiguration.

=Method 1=
Using serial adaptor.

The proposed procedure is to connect to the Emonwrt3 using serial (USB). Enter failsafe and reset the OS. Then re-install Emonwrt3 software.

==Hardware==
[[File:Ftdi-usb-to-ttl-serial-converter-adapter-ft232rl.jpg | right | 150px]]
* A [http://lechacalshop.com/gb/various/36-ftdi-usb-to-ttl-serial-converter-adapter-ft232rl.html USB to UART adaptor] (See picture).
* 3 jumper wires.

Other hardware needed are:
* A computer with a USB port.
* A common network cable. (cat5 / RJ45).

==Hardware Setup==
[[File:IMG_1830_small.png| right | 150px]]
* Remove the Microcontroller from the Base Board. This is the wide 28 pins chip. This must be taken off the board.
* Setup the USB adaptor for 3.3V using the small jumper.
* Connect the USB adator to the (Gnd,Rx,Tx) connect on the base board. The USB adaptor also has (Gnd,Rx,Tx). Connect them together.
* Connect the USB adaptor to your computer. A red light should be lit.

It should look as this picture here in the end.

==Software Preparation==

===Putty===
[[File:Putty_example_01.png | right | 150px]]

[https://www.chiark.greenend.org.uk/~sgtatham/putty/latest.html Download the Putty software from the web]. Install it on your computer.

Start Putty and setup a serial connection.
* '''Serial Line''' /dev/ttyUSB0 (or equivalent for windows or mac).
* '''Speed''' 115200

Click on '''Open'''. A black background window will appear.

==Enter Failsafe==
[[File:Failsafe.png | right | 150px]]

Power up the base board. Then wait until you see a message proposing to enter Failsafe mode.

When this appear enter '''f''' then return.

A prompt will be offered then enter here:

 firstboot -y

That's it. The operating system is back to factory default. You will now need to reinstall Emonwrt3.

==Complete installation==

Power off and on the base board and follow the guide below to install Emonwrt3.

[[Emonwrt3 Install on OpenWrt]]


=Method 2=
Using arduino sketch.

The proposed procedure is to flash the arduino chip with a special code. This will trigger uboot prompt on the SKW71 module. Then update the firmware via a web browser.

==Hardware==
* An Arduino UNO.
* A computer with a USB port.
* A common network cable. (cat5 / RJ45).

==Hardware Setup==

* Remove the Microcontroller from the Base Board. This is the wide 28 pins chip. 
* Insert the microcontroller on the Arduino UNO.

==Software Preparation==

===Arduino===

Open the Arduino IDE and copy paste this sketch below:

 void setup() {
  Serial.begin(115200);
  delay(500);
  Serial.println();
  delay(500);
  Serial.println("httpd");
 }
 void loop() {}

Upload the sketch to the arduino Uno.

===OpenWRT===

[http://archive.openwrt.org/chaos_calmer/15.05.1/ar71xx/generic/openwrt-15.05.1-ar71xx-generic-tl-wr703n-v1-squashfs-sysupgrade.bin Download OpenWRT Chaos Calmer here]. Save this somewhere on your computer.

==Enter uboot prompt==

[[File:Uboot_splash_01.png | right | 150px]]

Install the Arduino chip back onto the Emonwrt3 base board unit.

Connect the network cable directly from the computer to the EmonWRT3 unit.

Setup the computer with static IP address 192.168.1.2

Now power on the Emonwrt3 by connecting the micro-usb cable.

You can now access uboot going to address
 http://192.168.1.1
A page like the picture will appear.

Then choose the previously downloaded file to flash the OpenWRT OS.

Once complete do not forget to replace the Arduino firmware with the original one. Download it here [[EMONWRT3#Files]]

==Complete installation==

Power off and on the base board and follow the guide below to install Emonwrt3.

[[Emonwrt3 Install on OpenWrt]]