RPICT3V1

From lechacal
Jump to navigation Jump to search

Link to shop

This page is for board specific information. More information can be found on the generic page for RPICT series.

  • 3 AC current sensor
  • 1 AC Voltage sensor.
  • Compute real power.
  • Fit on Raspberrypi 2 holes mounting pattern.
  • Attiny84 Mcu


Compatibility

Version Compatible?
Raspberrypi 1 A Yes
Raspberrypi 1 B+ Yes
Raspberrypi 2 B Yes
Raspberrypi 3 B Yes
Raspberrypi 3 B+ Yes

Recommended sensors

  • AC Current sensor: SCT-013-000
  • AC Voltage sensor:
    • UK: 77DB-06-09
    • EU: 77DE-06-09
    • US: 77DA-10-09

Configuration

Starting from sketch version 1.1 the RPICT3V1 is configured over serial.

See general instructions for configuration below:

Configuration over serial for sketch version 1.1.

Configuration over serial for sketch version 1.2.

View the data with Python

Please note the configuration must have Emonhub format enabled (format=3). The example script below will be a good starting point.

First of all make sure you have python-serial package installed

$ sudo apt-get install python-serial

Then copy the following into an executable file and run it.

#!/usr/bin/python
import serial
ser = serial.Serial('/dev/ttyAMA0', 38400)

try:
       while 1:
               response = ser.readline()
               z = response.split(" ")
               if len(z)>=7:
                       print "RealP 1: %s Watts" % z[1]
                       print "RealP 2: %s Watts" % z[2]
                       print "RealP 3: %s Watts" % z[3]
                       print "Irms 1: %s mA" % z[4]
                       print "Irms 2: %s mA" % z[5]
                       print "Irms 3: %s mA" % z[6]
                       print "Vrms   : %s Volts" % z[7][:-2]
except KeyboardInterrupt:
       ser.close()

Emoncms Config (Emonhub)

For default configuration.

 [[11]]
   nodename = my_RPICT3V1
   hardware = RPICT3V1
   [[[rx]]]
      names = RP1, RP2, RP3, Irms1, Irms2, Irms3, Vrms
      datacode = 0
      scales = 1,1,1,1,1,1,1
      units =W,W,W,mA,mA,mA,V

Using the default sketch the output will be
NodeID Realpower1 Realpower2 Realpower3 Irms1 Irms2 Irms3 Vrms

  • RealPower in Watts
  • Irms in MilliAmps
  • Vrms in Volts

Sketch

Units are sold flashed with sketch for use with Voltage sensor.

Usage with Voltage sensor

Version 1.0
Version 1.1
Version 1.2

Usage without Voltage sensor

If you wish to use the board without using the voltage sensor use the sketch below. Note power will be estimated power only using fixed voltage setup in configuration.
No Voltage Version 1.0
No Voltage Version 1.1
No Voltage Version 1.2

Once the sketch uploaded write the configuration as follow:

$ wget lechacal.com/RPICT/config/A0/rpict3t1.conf
$ ./lcl-rpict-config.py -w rpict3t1.conf

* rpict3t1 above is not a tipo

Related Pages

How to calibrate the Voltage Port

Use Emonhub with RPICT

Howto setup rpi3 for CSV reading

How to program an Attiny85 or Attiny84