RPICT4T4: Difference between revisions
Jump to navigation
Jump to search
(→Files) |
|||
(5 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
[[File: | [[File:IMG_1814_small.png | 300px | right]] | ||
[http://lechacalshop.com/en/internetofthing/15-raspberrypi-4-current-sensor-adaptor-4-temperature-emoncms.html Link to shop] | [http://lechacalshop.com/en/internetofthing/15-raspberrypi-4-current-sensor-adaptor-4-temperature-emoncms.html Link to shop] | ||
Line 9: | Line 9: | ||
* Attiny84 Mcu | * Attiny84 Mcu | ||
=Compatibility= | |||
{| class="wikitable" | |||
|+ | |||
|- | |||
!Version | |||
!Compatible? | |||
|- | |||
|Raspberrypi 1 A | |||
|No | |||
|- | |||
|Raspberrypi 1 B+ | |||
|Yes | |||
|- | |||
|Raspberrypi 2 B | |||
|Yes | |||
|- | |||
|Raspberrypi 3 B | |||
|Yes | |||
|- | |||
|Raspberrypi 3 B+ | |||
|Yes | |||
|- | |||
|} | |||
==Current Sensor== | ==Current Sensor== | ||
[[File:IMG_1542_small.png | right | 300px]] | [[File:IMG_1542_small.png | right | 300px]] | ||
Recommended sensor: SCT-013-000 | Recommended sensor: SCT-013-000 | ||
For AC current only. | For AC current only. | ||
Line 78: | Line 99: | ||
[http://lechacal.com/RPICT/4CT4T/RPICT4T4_v1_4.ino Sketch version 1.4] | [http://lechacal.com/RPICT/4CT4T/RPICT4T4_v1_4.ino Sketch version 1.4] | ||
[http://lechacal.com/RPICT/4CT4T/RPICT4T4_v1_5.ino Sketch version 1.5] | |||
[http://lechacal.com/RPICT/4CT4T/RPICT4T4_v1_6.ino Sketch version 1.6] | |||
==Related Pages== | ==Related Pages== | ||
[[ | [[Howto_setup_Raspbian_for_serial_read]] | ||
[[How to program an Attiny85 or Attiny84]] | [[How to program an Attiny85 or Attiny84]] |
Revision as of 09:53, 9 January 2019
This page is for board specific information. More information can be found on the generic page for RPICT series.
- 4x AC Current Sensors
- 4x DS18B20 Temperature Sensors
- Attiny84 Mcu
Compatibility
Version | Compatible? |
---|---|
Raspberrypi 1 A | No |
Raspberrypi 1 B+ | Yes |
Raspberrypi 2 B | Yes |
Raspberrypi 3 B | Yes |
Raspberrypi 3 B+ | Yes |
Current Sensor
Recommended sensor: SCT-013-000
For AC current only.
Temperature Sensor
Connector: 3.5mm Jack
The intended temperature sensor is the DS18B20.
The connector is a 3 way screw terminal connector.
Configuration
Starting from sketch version 1.4 the RPICT4T4 is configured over serial.
See general instructions for configuration over serial.
Emoncms Config (Emonhub)
For default configuration.
[[11]] nodename = RPICT4T4 hardware = RPICT4T4 [[[rx]]] names = Power1, Power2, Power3, Power4, T1, T2, T3, T4 datacode = 0 scales = 1,1,1,1,1,1,1,1 units = W,W,W,W,C,C,C,C
Python Example
Please note the uploaded sketch must have CSV enabled. The example script below will be a good starting point.
First of all make sure you have python-serial package installed
$ sudo apt-get install python-serial
Then copy the following into an executable file and run it.
#!/usr/bin/python import serial ser = serial.Serial('/dev/ttyAMA0', 38400) try: while 1: response = ser.readline() z = response.split(",") if len(z)>6: print "Power 1: %s Watts" % z[0] print "Power 2: %s Watts" % z[1] print "Power 3: %s Watts" % z[2] print "Power 4: %s Watts" % z[3] print "Temperature 1: %s C" % z[4] print "Temperature 2: %s C" % z[5] print "Temperature 3: %s C" % z[6] print "Temperature 4: %s C" % z[7][:-2] except KeyboardInterrupt: ser.close()