RPICT7V1 v2.0: Difference between revisions

From lechacal
Jump to navigation Jump to search
Line 64: Line 64:
Using a serial line terminal program one can configure the following:
Using a serial line terminal program one can configure the following:
  - Polling interval
  - Polling interval
  - Output format (csv or emoncms)
  - Output format (csv or emonhub)
  - Calibration values (Voltage and Current)
  - Calibration values (Voltage and Current)
  - Voltage/current combinations for real power computation.
  - Voltage/current combinations for real power computation.

Revision as of 17:01, 29 March 2019

RPICT7V1 (This covers for both hardware versions 2 and 3)

Link to shop

This page is for board specific information. More information can be found on the generic page for RPICT series.

  • 7 AC current sensors.
  • 1 AC Voltage sensor.
  • Measure RMS Current and Voltage, Active power, Apparent Power, Power Factor.
  • Fit on Raspberrypi 4 holes mounting pattern.
  • AtMega328 Mcu (Arduino UNO)
  • MCP3208 ADC
  • Stackable with itself, RPICT8 and RPICT4V3.


Compatibility

Version Compatible?
Raspberrypi 1 A No
Raspberrypi 1 B+ Yes
Raspberrypi 2 B Yes
Raspberrypi 3 B Yes
Raspberrypi 3 B+ Yes

Recommended sensors

  • AC Current sensor:
    • SCT-013-000
    • SCT-019
    • SCT-006
  • AC Voltage sensor:
    • UK: 77DB-06-09
    • EU: 77DE-06-09
    • US: 77DA-10-09

VOLTAGE OUTPUT CT ARE NOT COMPATIBLE WITH THIS BOARD.

Stacking Configuration

General stacking information is described in the RPICT stacking page. RPICT_Stacking

Software Configuration

Using a serial line terminal program one can configure the following:

- Polling interval
- Output format (csv or emonhub)
- Calibration values (Voltage and Current)
- Voltage/current combinations for real power computation.
- Output channels

The documentation for serial configuration can be found on this page.
Over Serial Configuration - Sketch 2.2
Over Serial Configuration - Sketch 2.3
Over Serial Configuration - Sketch 2.4
Over Serial Configuration - Sketch 2.5
Over Serial Configuration - Sketch 2.6
Over Serial Configuration - Sketch 2.8

Over Serial Configuration - Sketch 3.0

The board can be configured with the online configurator.

Files

Default Sketch

Default Sketch V2.5.

Default Sketch V2.6.

Default Sketch V2.7.1.

Default Sketch V2.8.0.

Default Sketch V3.0.0.

Default Sketch V3.0.1.

(note boards are sold already flashed with latest firmware).

noOSC Sketch

The Default sketch allows up to 28 computation nodes to be run. If more are needed for higher stacks then we recommend to use the noOSC sketch. This is the same as the default sketch but Over Serial Configuration (OSC) as been removed to allow up to 40 nodes to be computed. Configuration has to be edited in the sketch.

noOSC Sketch v1.0
noOSC Sketch v1.1

Emoncms Config (Emonhub)

Make sure you read this first.

For default configuration. Used as single board only (not stacked).

 [[11]]
   nodename = my_RPICT7V1
   hardware = RPICT7V1
   [[[rx]]]
      names = RP1, RP2, RP3, RP4, RP5, RP6, RP7, Irms1, Irms2, Irms3, Irms4, Irms5, Irms6, Irms7, Vrms
      datacode = 0
      scales = 1,1,1,1,1,1,1,1,1,1,1,1,1,1,1
      units =W,W,W,W,W,W,W,mA,mA,mA,mA,mA,mA,mA,V


Related Pages

Use Emonhub with RPICT

Howto setup rpi3 for CSV reading

How to calibrate the Voltage Port

Update RPICT firmware (CT7V1/CT4V3/CT8)