RPICT7V1: Difference between revisions
| (8 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
This product is deprecated. [[RPICT7V1_v2.0]] replaces it. | |||
[http://lechacalshop.com/en/internetofthing/8-raspberrypi-7x-current-sensor-adaptor-1-voltage-emoncms.html Link to shop] | [http://lechacalshop.com/en/internetofthing/8-raspberrypi-7x-current-sensor-adaptor-1-voltage-emoncms.html Link to shop] | ||
==Overview== | |||
This is RPICT7V1 version 1. This version does not support over serial configuration. | |||
This page is for board specific information. More information can be found on the [[Raspberrypi_Current_and_Temperature_Sensor_Adaptor | generic page for RPICT series]]. | |||
* 7 AC current sensor | * 7 AC current sensor | ||
| Line 17: | Line 27: | ||
** UK: 77DB-06-09 | ** UK: 77DB-06-09 | ||
** EU: 77DE-06-09 | ** EU: 77DE-06-09 | ||
** US: 77DA-10-09 | ** US: 77DA-10-09 | ||
| Line 55: | Line 65: | ||
[http://lechacal.com/RPICT/7CT1V/RPICT7V1_v1_2.ino Default Sketch V1.2.]<br> | [http://lechacal.com/RPICT/7CT1V/RPICT7V1_v1_2.ino Default Sketch V1.2.]<br> | ||
[http://lechacal.com/RPICT/7CT1V/SendOnlySoftwareSerial.zip SendOnlySoftwareSerial.zip] | [http://lechacal.com/RPICT/7CT1V/SendOnlySoftwareSerial.zip SendOnlySoftwareSerial.zip] | ||
==Sketch Upload== | ==Sketch Upload== | ||
| Line 70: | Line 76: | ||
==Related Links== | ==Related Links== | ||
[[How to calibrate the Voltage Port]] | [[How to calibrate the Voltage Port]] | ||
[[How_to_program_an_Attiny85_or_Attiny84]] | |||
[[Howto setup Raspbian for serial read]] | |||
Latest revision as of 19:17, 7 April 2019
This product is deprecated. RPICT7V1_v2.0 replaces it.
Overview
This is RPICT7V1 version 1. This version does not support over serial configuration.
This page is for board specific information. More information can be found on the generic page for RPICT series.
- 7 AC current sensor
- 1 AC Voltage sensor.
- Compute real power.
- Fit on Raspberrypi 4 holes mounting pattern.
- Attiny84 Mcu
Recommended sensors
- AC Current sensor: SCT-013-000
- AC Voltage sensor:
- UK: 77DB-06-09
- EU: 77DE-06-09
- US: 77DA-10-09
EmonCMS Output
Using the default sketch the output will be
NodeID Realpower1 Realpower2 Realpower3 Realpower4 Realpower5 Realpower6 Realpower7 Irms1 Irms2 Irms3 Irms4 Irms5 Irms6 Irms7 Vrms
- RealPower in Watts
- Irms in MilliAmps
- Vrms in Volts
Emoncms Config
For default sketch v1.2
[[11]]
nodename = my_RPICT7V1
firmware = v1.2
hardware = RPICT7V1
[[[rx]]]
names = Realpower1, Realpower2, Realpower3, Realpower4, Realpower5, Realpower6, Realpower7,Irms1, Irms2, Irms3, Irms4,Irms5,Irms6,Irms7,Vrms
datacode = h
scales = 1,1,1,1,1,1,1,1,1,1,1,1,1,1,1
units =W,W,W,W,W,W,W,mA,mA,mA,mA,mA,mA,mA,V
CSV Output
Using the default sketch the output will be
Realpower1, Realpower2, Realpower3, Realpower4, Realpower5, Realpower6, Realpower7,Irms1, Irms2, Irms3, Irms4, Irms5, Irms6, Irms7, Vrms
- RealPower in Watts
- Irms in MilliAmps
- Vrms in Volts
Files
Default Sketch V1.2.
SendOnlySoftwareSerial.zip
Sketch Upload
To upload the sketch the three jumper at the center of the board must be removed.
An avr programmer with 6pin ribbon cable is needed for programming.
Related Links
How to calibrate the Voltage Port