RPICT7V1 Version 4

RPICT7V1 (This covers for hardware versions 4)

Link to shop

This page is for board specific information. More information can be found on the generic page for RPICT series.

The RPICT7V1 is the same unit as earlier version RPICT7V1_v2.0 but with top end instrumentation amplifiers. This can be considered as the Ferrari of the RPICT series.

• 7 AC current sensors.
• 1 AC Voltage sensor.
• Measure RMS Current and Voltage, Active power, Apparent Power, Power Factor.
• Fit on Raspberrypi 4 holes mounting pattern.
• AtMega328 Mcu (Arduino UNO)
• MCP3208 ADC
• High precision Instrumentation Amplifier AD623.
• Supports both Current and Voltage output CT.

Compatibility

Version	Compatible?
Raspberrypi 1 A	No
Raspberrypi 1 B+	Yes
Raspberrypi 2 B	Yes
Raspberrypi 3 B	Yes
Raspberrypi 3 B+	Yes

Recommended Sensors

AC Current

Both current and voltage output are supported.

• Current Output CT
  • SCT-013-000
  • SCT-019
  • SCT-006
• Voltage Output CT
  • SCT-013-005
  • SCT-013-010
  • SCT-013-015
  • SCT-013-020
  • SCT-013-025
  • SCT-013-030
  • SCT-013-050
  • SCT-013-060;

For Current output CT the RPICT board must have a burden resistor fitted.

For voltage output CT there is no need for a burden resistor. The pro for this is the ability for the user to be able to change CT using the same RPICT7V1 Version 4 unit. Only the calibration coefficient has to be modified in the configuration.

AC Voltage sensor

220V 240V & 110V

• UK: 77DB-06-09
• EU: 77DE-06-09
• US: 77DA-10-09

400V or more

• ZMPT101B

There are current development working on the ZMPT101B which has excellent measuring capability. Voltage up to 1000V can be measured. Contact us for more information.

Amplification Level

The new feature about RPICT7V1 Version 4 is the addition of instrumentation amplifiers AD623. This brings very sensitive and accurate method to measure physical values. Outstanding stability of the results have also been noticed.

Moreover the amplification level allows for more flexibility on the choice of the burden resistor. The scale is no longer depending on it. Hence improving on the linearity of the CT output for low current readings.

Read the following page to find out how resistors are calculated.
Amplification RPICT7V1 Version 4

Stacking Configuration

Version 4 can not be stacked at this stage. Contact us for enquiries on stacking development.

Software Configuration

Using a serial line terminal program one can configure the following:

- Polling interval
- Output format (csv or emonhub)
- Calibration values (Voltage and Current)
- Voltage/current combinations for real power computation.
- Output channels

The documentation for serial configuration can be found on this page.

Over Serial Configuration - Sketch 3.0

The board can be configured with the online configurator.

Files

Default Sketch

Default Sketch V3.0.2.

Emoncms Config (Emonhub)

Make sure you read this first.

For default configuration. Used as single board only (not stacked).

 [[11]]
   nodename = my_RPICT7V1
   hardware = RPICT7V1
   [[[rx]]]
      names = RP1, RP2, RP3, RP4, RP5, RP6, RP7, Irms1, Irms2, Irms3, Irms4, Irms5, Irms6, Irms7, Vrms
      datacode = 0
      scales = 1,1,1,1,1,1,1,1,1,1,1,1,1,1,1
      units =W,W,W,W,W,W,W,mA,mA,mA,mA,mA,mA,mA,V

Related Pages

Use Emonhub with RPICT

Howto setup Raspbian for serial read

How to calibrate the Voltage Port

Update RPICT firmware (CT7V1/CT4V3/CT8)